Skip to content
Home » Attenuation, Distortion and Noise

Attenuation, Distortion and Noise

1. Introduction

When a signal travels from a sender to a receiver through a communication medium, its quality may decrease. The unwanted effects that cause the signal to become weaker or changed are called transmission impairments.

The three major transmission impairments are:

  1. Attenuation
  2. Distortion
  3. Noise

λobservation point\(v = f\lambda\)

A simple representation is:

Sender                         Receiver
  |                               |
  |  Original Signal              |
  | ~~~~~~~~~~~~~~~~~~~~~~~~      |
  |                               |
  +------ Communication ----------+
           Medium
              ↓
       Transmission
        Impairments
              ↓
   Weaker / Changed / Noisy
          Signal

1. Attenuation

Definition

Attenuation means the loss of signal strength as the signal travels through the transmission medium.

In simple words:

Attenuation = Signal becomes weaker with distance.

For example, if you shout from a short distance, your voice is loud. As the distance increases, the sound becomes weaker. Communication signals behave similarly.

Diagram

Sender                         Receiver

Strong Signal                  Weak Signal
    |                               |
    ↓                               ↓

  ~~~~~~~~      →      ~~~~~~      →   ~~~

The signal gradually loses energy while travelling.

Causes of Attenuation

  • Long transmission distance
  • Resistance of cables
  • Poor-quality transmission media
  • Absorption of signal energy
  • Environmental conditions

Measurement

Attenuation is commonly measured in decibels (dB).

A commonly used expression is:\[ Attenuation(dB)=10\log_{10}\left(\frac{P_{transmitted}}{P_{received}}\right) \]

where:

  • \(P_{transmitted}\) = transmitted power
  • \(P_{received}\) = received power

How to reduce attenuation?

  • Use better-quality cables
  • Use repeaters or amplifiers
  • Reduce transmission distance
  • Use fiber-optic cable for long-distance communication

Example

Suppose a signal is transmitted with power of 100 mW and received with power of 25 mW.\[ Attenuation=10\log_{10}\left(\frac{100}{25}\right) \]\[ =10\log_{10}(4) \]\[ \approx 6.02\,dB \]

So the signal has approximately 6 dB attenuation.


2. Distortion

Definition

Distortion occurs when the shape or form of the original signal changes during transmission.

In simple words:

Distortion = Signal shape changes.

Unlike attenuation, where the signal mainly becomes weaker, distortion changes the shape or characteristics of the signal.

Diagram

Original Signal

      /‾\      /‾\
_____/   \____/   \____


Distorted Signal

     /‾\       /\
____/   \_____/  \____

The receiver does not receive exactly the same waveform that was transmitted.


Causes of Distortion

Different frequency components of a signal may travel through a medium at different speeds or experience different attenuation.

As a result, the components do not arrive at the receiver in exactly the same way or at the same time.

Distortion can occur because of:

  • Different propagation speeds
  • Different attenuation at different frequencies
  • Imperfections in transmission media
  • Limited bandwidth of the channel

Example

Suppose a signal contains three frequency components:

Signal = f1 + f2 + f3

If the transmission medium affects these frequencies differently:

f1 → slightly delayed
f2 → normal
f3 → more delayed

The combined signal can become distorted.

How to reduce distortion?

  • Use a suitable bandwidth
  • Use high-quality transmission media
  • Use equalizers
  • Use appropriate signal processing techniques

3. Noise

Definition

Noise is an unwanted electrical or electromagnetic signal that gets added to the original signal during transmission.

In simple words:

Noise = Unwanted signal added to the original signal.

Diagram

Original Signal
      +
   Noise
      ↓
Received Signal

For example:

Original:

─────┐    ┌─────┐
     └────┘     └────

With Noise:

─~───┐~──┌─~───┐~~
     └─~─┘     └──~

The receiver may have difficulty identifying the original signal when noise is high.


Types of Noise

There are several types of noise.

A. Thermal Noise

Thermal noise is caused by the random movement of electrons inside electronic components and communication systems.

It is also called Johnson noise.

It is present to some extent in electronic systems.


B. Induced Noise

Induced noise occurs when signals from other electrical or electromagnetic sources interfere with the communication signal.

Examples:

  • Electric motors
  • Power lines
  • Electrical equipment

C. Crosstalk

Crosstalk occurs when the signal from one communication channel interferes with another nearby channel.

Example:

Cable 1  ────────────────
              ↓
           Interference
              ↓
Cable 2  ────────────────

A common example is unwanted interference between wires in a communication cable.


D. Impulse Noise

Impulse noise consists of short-duration, high-energy disturbances.

Examples:

  • Lightning
  • Switching equipment
  • Electrical sparks

It can cause sudden errors in transmitted data.


4. Signal-to-Noise Ratio (SNR)

One important concept related to noise is Signal-to-Noise Ratio (SNR).

It compares the strength of the desired signal with the strength of the noise.\[ SNR = \frac{P_{signal}}{P_{noise}} \]

It is commonly expressed in decibels:\[ SNR(dB)=10\log_{10}\left(\frac{P_{signal}}{P_{noise}}\right) \]

Important point

Higher SNR = Better signal quality

Lower SNR = More noise and poorer signal quality

Example

Suppose:

  • Signal power = 100 mW
  • Noise power = 1 mW

Then:\[ SNR=\frac{100}{1}=100 \]\[ SNR(dB)=10\log_{10}(100)=20dB \]

Therefore, the SNR is 20 dB.


5. Attenuation vs Distortion vs Noise

FeatureAttenuationDistortionNoise
MeaningSignal becomes weakerSignal shape changesUnwanted signal is added
Main effectLoss of strengthChange in waveformInterference
Main causeDistance/mediumDifferent treatment of frequenciesElectrical/environmental interference
MeasurementdBDepends on signal characteristicsSNR/dB often used
ExampleWeak signal after long cableChanged waveformElectrical interference
SolutionAmplifier/repeaterEqualizer/better mediumShielding/filtering

6. Easy Way to Remember

Remember the three words:

A-D-N

A — Attenuation → Amplitude decreases

Strong → Weak

D — Distortion → Shape changes

Original shape → Changed shape

N — Noise → New unwanted signal added

Original + Unwanted signal

7. Real-Life Example

Suppose you are watching a video through a network connection.

Attenuation

The signal becomes weak because the transmission distance is large.

Distortion

The signal waveform changes because different components of the signal are affected differently.

Noise

Electrical interference or other signals are added to the communication signal.

Therefore:

Original Signal
      ↓
Transmission Medium
      ↓
┌─────────────────────┐
│ Attenuation → Weak  │
│ Distortion  → Shape │
│ Noise       → Interference │
└─────────────────────┘
      ↓
Received Signal

Conclusion

Transmission impairments reduce the quality and reliability of communication.

  • Attenuation makes the signal weaker.
  • Distortion changes the shape of the signal.
  • Noise adds unwanted signals to the original signal.

These impairments are important in the Physical Layer because they can cause data errors, poor communication quality and loss of information.

⭐ MCA 10-Mark Question

“What are transmission impairments? Explain attenuation, distortion and noise with suitable diagrams. Also explain the different types of noise and Signal-to-Noise Ratio.”